Regenerative AC and DC Test Power
The AZX Series is a family of high power, single, split and three phase, AC, DC and AC+DC output capable Power Sources with full energy recovery to the AC mains when sinking power from the equipment under test. Available models range from 30 kVA to 440 kVA. Using a modern color touch screen based user interface for ease of use, the AZX Series is cost effective and fully programmable for both basic frequency conversion and advanced AC power line or DC power disturbance test applications requiring up to 1000 Hz fundamental frequencies.
The energy recovery capability allows both sourcing and sinking of current and power up to 100% of rated power. Adding the Load Option (Option L) adds full electronic regenerative AC & DC Load programming capability to the AZX
The AZX Series consists of a range of High Power Switching AC, DC and AC+DC capable Power Sources with regenerative capability to support both sourcing and sinking of current and power. Energy recovery to the grid enables testing of products using only a fraction of the required grid power when compared to using non-regenerative power sources, saving cost. The AZX also supports testing of grid-teid products like wind and solar inverters, energy storage systems (ESS) and electric Vehicle to Grid (V2G) and Vehicle to Home discharge systems.
Covering a power range from 30 kVA to 440 kVA. All AZX models offer single, split and three phase output configurations. The AZX is a state-of-the-art design using Silicon Carbide (SiC) power devices for enhanced performance.
Great emphasis has been placed on energy efficiency, ease of installation, and maximum power. Control and operational features provide a high degree of application versatility and ease of use for the test engineer. Applications range from simple, manually controlled frequency conversion to IEC power line emission and immunity testing and with sophisticated transient simulation. For defense and aviation applications, the AZX supports a fundamental frequency range up to 1000 Hz and dual AC voltage ranges of 0~225VLL and 0~440VLL respectively to support a wide range of avionics compliance test standards. In DC mode, voltage ranges are ±0~335Vdc and ±0~650Vdc.
The same voltage, power and current ranges are available when adding the Option L Electronic Load Mode. This open allows the AZX to be used as a regenerative programmable AC & DC electronic load. Available load modes are Constant Current (CP), Constant Resistance (CR), Constant Power (CP) and Circuit Emulation of linear and non-linear loads.
For Power Hardware in the Loop (HIL) Grid simulation applications, the AZX offers an optional high speed analog I/O for fast response (Option H)/
- * Fully Regenerative Operation with energy recovery to the AC grid
- * Source and Sink full Power and Current
- * AC Mode, DC Mode, AC+DC Mode or DC+AC Mode
- * DC, 15 to 1,000 Hz Frequency Range full power
- * Dual Constant Power mode AC Voltage Ranges 0~225V L-N and 0~440V L-N
- * Dual Constant Power mode DC Voltage Ranges 0~335V L-N and 0~650V L-N
- * Full power available in both AC and DC Modes
- * Precision True-RMS metering of Volts, Amps, Power, VA, Power Factor and Crest Factor
- * Waveform capture scope function for voltage and current on all phases
- * Harmonic measurement for voltage and current on all phases
- * Extensive Analog and Digital I/O for ATE and system integration
- * Available PPSC Manager Windows graphical user interface
- * Also compatible with legacy UPC Studio graphical user interface
- * 1, 2 or 3 Phase Selectable Output from front panel or bus command
- * Sine, Square, Triangle, THD and Arbitrary waveforms
- * 3 Phase AC input with Active PFC, selectable input voltage
- * 200 stored programs for both static and dynamic Transient Testing
- * LIST, PULSE and STEP Transient Modes
- * Continuous Self Calibration (CSC)
- * Precision Voltage Programming - 0.02% with CSC engaged in AC and DC modes
- * Standard Models in Power Levels from 30 kVA to 200 kVA. Contact us for higher power.
- * Standard RS-232, USB, GPIB and Ethernet Interface with SCPI compatibility
- * LXI Compliant LAN/Ethernet with embedded web server
- * IVI Instruments drivers
- * CE (EMC/Safety) Marked
Regenerative AC or DC Test Power
The AZX Series Power Source can both source and sink current and power from an EUT making and can thus act as a Grid Simulator for testing of grid connected energy producing products like PV Inverters or EV Chargers. In DC mode, the AZX can be used to charge and discharge large battery packs up to 1000Vdc using series output mode.
Electronic Load Applications
The AZX power source can be used as an electronic load by adding the “L” option. With this option, full electronic load capabilities are added in both AC and DC mode. Regenerative Loads save cost by reducing electricity use and heat generation. They also allow testing of higher power EUTs as most of the power sent to the AZX load is regenerated back on the gird so the test lab power feed only has to cover the losses of the test equipment used and the EUT.
Supported Load Modes are Constant Current (CC), Constant Resistive (CR), Constant Power (CP) and Circuit Emulation (CE). Voltage, power and current ranges remain the same as in Voltage Source or Current Source modes.
AC+DC Test Power
Special test requirements such the application of a DC offset on an AC line or AC ripple on a DC supply output are supported by selecting the AC+DC Mode of operation.
EMC Compliance Test Power
The AZX Series is also used for our line of Power Line Emissions and Immunity EMC Test Systems, the ECTS2 Series where grid connected energy producing products need to be tested. These systems are used to test for compliance to IEC Harmonics, Flicker and Immunity for AC power or DC power products that must meet CE mark requirements for export to Europe.
Frequency/Voltage Conversion
The AZX Series is an excellent source of stable AC voltage over the frequency range of 1 to 1,000 Hz. The output frequency is accurate to 0.01%.
Phase Conversion
With the ability to provide singe, split and three-phase outputs, the AZX Series is the perfect choice to provide 1 Phase to 2 or 3 Phase or 3 Phase to 1 Phase conversion.
Controller
The AZX Series controller offers both manual and full programmable control. Front panel operation is menu driven using a combination of direct access menu keys to the left of the large color display and 5 soft keys located on the right of the display. The rotary knob can be used to scroll through menu fields and doubles as an ENTER key. The same knob allows for slewing of output parameters. A full decimal keypad is provided as well for direct parameter entry. The AZX can also be operated remotely from one of its included remote interfaces. Operation from a web browser via LAN or USB is also supported through the embedded web server of the AZX.
Model Comparison
Model | Phase Mode | Rated Power(1) (AC/DC) | Voltage Ranges | Max, AC/DC Current High V Range(2) | Max, AC/DC Current Low V Range(2) | Form Factor |
---|---|---|---|---|---|---|
3300AZX | 1,2 & 3 | 30 kVA, kW 30 kW | 225Vac/440Vac ±335Vdc/±650Vdc | 45Arms 30Adc | 90Arms 60Adc | 34U Cabinet |
3450AZX | 1,2 & 3 | 45 kVA, kW 45 kW | 225Vac/440Vac ±335Vdc/±650Vdc | 65Arms 40Adc | 110Arms 80Adc | 34U Cabinet |
3550AZX | 1,2 & 3 | 55 kVA, kW 55 kW | 225Vac/440Vac ±335Vdc/±650Vdc | 75Arms 50Adc | 130Arms 100Adc | 34U Cabinet |
3900AZX | 1,2 & 3 | 90 kVA, kW 90 kW | 225Vac/440Vac ±335Vdc/±650Vdc | 130Arms 80Adc | 220Arms 160Adc | 2 x 34U Cabinet |
31100AZX | 1,2 & 3 | 110 kVA, kW 110 kW | 225Vac/440Vac ±335Vdc/±650Vdc | 150Arms 100Adc | 260Arms 200Adc | 2 x 34U Cabinet |
31650AZX | 1,2 & 3 | 165 kVA, kW 165 kW | 225Vac/440Vac ±335Vdc/±650Vdc | 225Arms 150Adc | 390Arms 300Adc | 3 x 34U Cabinet |
32200AZX | 1,2 & 3 | 220 kVA, kW 220 kW | 225Vac/440Vac ±335Vdc/±650Vdc | 300Arms 200Adc | 520Arms 400Adc | 4 x 34U Cabinet |
Note 2: Current shown for 3 Phase or Split phase mode. For single phase mode, current is times 3.